Ver versión completa : PROGRAMAR DOBLE SERVO DE ELEVADOR EN SPEKTRUM DX7
Alguien sabe si se puede programar dos servos para elevador con el Spektrum DX7?? He intentado varios metodos y siempre me queda con los trims separados....es decir, si mueves el trim del elevador solo se mueve un servo y el otro no....:confused::(:mad:
El chiste es evitar las Y-harness con reversible...
HELP!!!:(
FranciscoOrtiz
28-01-2009, 11:27 PM
Alguien sabe si se puede programar dos servos para elevador con el Spektrum DX7?? He intentado varios metodos y siempre me queda con los trims separados....es decir, si mueves el trim del elevador solo se mueve un servo y el otro no....:confused::(:mad:
El chiste es evitar las Y-harness con reversible...
HELP!!!:(
Milo, es muy sencillo, utiliza las mezclas programables, si mal no recuerdo las dos ultimas tienen la capacidad de ajuste de doble trim
angelo08
28-01-2009, 11:37 PM
hola Milo mira se tiene que utilizar en la mezcla numero 5 porque si lo haces de la 1 a la 4 te quedan trims separados yo las utilizo asi suerte
Martin G.
Muchisimas gracias Paco y Martin! Voy a intentarlo y les comento como me fue! Es una frustracion enorme moverle al radio por dos horas y no llegar a ningun lado....:D
alcarafa
29-01-2009, 01:53 AM
MILO AQUI ESTÁ LA RESPUESTA, NO TE ROMPAS MÁS LA CABEZA, :D.
Dual ELEVATOR and DUAL Ailerons -
Posted by Mike McConville, Horizon Hobby, on RC Universe
( http://www.rcuniverse.com/forum/fb.asp?m=5269071 (http://www.rcuniverse.com/forum/fb.asp?m=5269071))
On set-up of models with 2 ail and 2 elev servos, I'd like to share the proper and fastest way to do this.
First, the rx connections:
1. Right side elevator into ELEV channel
2. Left Side elevator into AUX 2 channel
3. Right Side aileron into AIL channel
4. Left side aileron into FLAP (AUX 1) channel
5. Rudder and Throttle into the normal channels
TX program
1. Go into the Set-up mode (hold down scroll and select keys while turning on tx)
2. Scroll to the Input Select screen
3. Set Aux2 to INH, AUX2 TRIM to INH, FLAP to INH, FLAP TRIM to INH
This turns off both of these channels from the levers and switches. This is the proper way to do this, not using P-mixes or Travel adjust.
4. Scroll to Wing Type
5. Activate Flaperon
Elevator Set up
1. Power off tx and turn back on. Go to normal programming mode
2. Scroll to P-mix 6 (or Mix 5 - mix 5 and 6 "master" trim changes into both master and slave channel. Mixes 1 through 4 do NOT - editor). Set ELEV as master and AUX2 as slave.
3. Scroll to Sub Trim and set the neutral for the right side elevator with ELEV channel and the neutral for the left side elevator with AUX2.
4. Scroll to Travel Adjust. Set the desired travel for the right side elevator with the ELEV adjustment.
5. Scroll back to P-Mix 6 and tweak the travel of the left side elevator to match the right side with the mix values, for each stick direction.
Aileron Set-up
1. Go to normal programming mode
2. Scroll to Sub Trim and set the neutral for the right side aileron with AILE channel and the neutral for the left side aileron with FLAP channel.
3. Scroll to Travel Adjust. Set the desired travel for the right side aileron with the AILE adjustment.
4. Set the travel of the left side aileron to match the right in both stick directions with the FLAP channel in Travel Adjust.
From here forward everything will work as if the elevator and ailerons were off of one channel. i.e. DR, expo, p-mixing for pitch or roll coupling.
Wow!! esta sencillo y yo andaba picando piedra por el lado equivocado...:o mejor explicado no puede estar...
Muchas gracias Rafa!! a veces los problemas mas dificiles tienen la solucion mas facil..:D
-Milo
alcarafa
29-01-2009, 09:38 PM
Milo di con este thread en rcuniverse, hace como un año cuando compre un yak 54 tiene más de 100 paginas y puedes encontrar todos los trucos y mezclas posibles, un tesoro para los que no conocen al 100% el DX7 y puedes aprender muchisimo tambíen.
este es el link: http://www.rcuniverse.com/forum/m_4888165/mpage_1/key_dx7/tm.htm